IRFP datasheet, IRFP pdf, IRFP data sheet, datasheet, data sheet, pdf , International Rectifier, V Single N-Channel HEXFET Power MOSFET in a. The IRFP and IRFP are advanced power MOSFETs designed, tested, and guaranteed to withstand a specified level of energy in the breakdown. IRFP, SiHFP Vishay Siliconix. FEATURES. • Dynamic dV/dt Rated. • Repetitive Avalanche Rated. • Isolated Central Mounting Hole. • Fast Switching.

Author: Maugal Douzuru
Country: Papua New Guinea
Language: English (Spanish)
Genre: Video
Published (Last): 28 January 2008
Pages: 165
PDF File Size: 13.61 Mb
ePub File Size: 5.87 Mb
ISBN: 384-9-63906-119-1
Downloads: 57888
Price: Free* [*Free Regsitration Required]
Uploader: Bragrel

Like to see a little higher drive voltage to fully turn on the FET. There is no need for the ohm irfp360 datasheet just reduces your drive. What datashret the light string?

IRFP (IRF) – Power Mosfet(vdss=v, Rds(on)=ohm, Id=23a) | eet

For opto-isolation, if I recall even the irfp360 datasheet should be fast enough for this application, and can handle higher voltages than the irfp360 datasheet if 7V is too low for driving the gate of the Datasueet.

I made a test setup like the img attached without c1 it was very unstable. I think people get into as much trouble with high speed drivers as they intend to solve. If this is for dimming, you should use an even steeper ratio. The flickering is probably the result of the PWM signal beeing modulated by the mains frequency. It may not be easy finding a logic level FET capable of V and irfp360 datasheet as requested, what is the current consumption of the lighting strip when fully on? Psi Super Contributor Posts: Drop me a message!

Check the pic again, He’s using 8.

Related Articles (10)  1756-OB16E DOWNLOAD

Use a logic level mosfetreason being normal type mosfet cannot be fully turned irfp360 datasheet by microprocessor output resulting in high resistance and heat built up in mosfet that’s why your circuit failed. In software I always eliminate short pulses at either end irfp360 datasheet only cause heating.

I measured the dc voltage on the strip without and whit caps and there was a almost 50v difference if I recall right. Where irfp360 datasheet the 8. Seekonk Super Contributor Posts: I tried running the optocoupler from a battery irfp360 datasheet same results.

(PDF) IRFP360 Datasheet download

I’m assuming you’re switching a DC light here. Performa01 Frequent Contributor Irfp360 datasheet Can’t be that hard to find a 48V or so wall wart, that is a lot of voltage to switch fast.

There was an error while thanking. What significance is the frequency?

Intersil Corp. IRFP Datasheet.

I am using the pwm from the atmega, the default hz is too small I would like hz or irfp360 datasheet I was thinking the optocoupler cannot handle the switching and consider using a 6n is the 4n25 irfp360 datasheet for this application or should I use something else? Please login or register. In a circuit like this with a weak pull-down and an incredibly massive gate chargeyou’ll be lucky to succeed at 1kHz.

Using irfp360 datasheet 6N and a MCP is the correct way to drive the mosfet, but using several kHz for driving a large led strip is not good and not necessary unless you add irfp360 datasheet inductor for smoothing the current.

IRFP360 Datasheet ( N-Channel MOSFET Transistor )

Nothing is quite like a great humming power-station. There irfp360 datasheet very simple dimmers on internet. A room-sized installation will definitely be a source of EMI! Did you miss your activation email? You irfp360 datasheet use faster opto coupler like 6N What purpose does it serve? T3sl4co1l Super Contributor Posts: Thank you for the reply, by irfp360 datasheet string I mean an V led strip in the irfp irfp360 datasheet I understood that the vgs is 10V the purpose is for dimming the led strip I use a rectifier bridge so the led strip is powered with DC could you recommend a logic level mosfet that can handle more than V dc and more than 10A current.

Related Articles (10)  DD FORM 1351-2 EBOOK DOWNLOAD

Try adding a capacitor after the rectifier to get a better dc voltage. The 10K resistor is too high, make it 1K or under. I have considered the 12v led strip option, but the price would be irfp360 datasheet higher, for 12v I would need a supply at each 5 m and much more amps to drive. Single transistor optoisolators, like 4N25, aren’t capable of switching much faster than a microsecond, suggesting a frequency below 50kHz.

What is the “8. Irfp360 datasheet LED string will see the same maximum voltage with or without a capacitor.

Another option would be to use a phase controlled triac with MOC optocoupler. BloodyCactus Frequent Irfp360 datasheet Posts: I think you would be better playing with lower voltages. The average current will increase because irfp360 datasheet the old “area under the curve. Hello, I want to drive a V led strip using the IRFP mosfet for driving from an arduino pin I use a 4n25 optocoupler like the schematic attached.